ARMING IN “EXIT” MODE EXIT is used when the user is away from the premises

How To Program Caddx Nx 8e Download Here's the factory provided installation and programming guides for current GE panels. A Very Quick Programming Guide For GE Panels As complicated as the GE program may look, there are only two things that need be changed for a typical DIY installation, those are: Zone Types in location 25. GE Caddx NX-8/SecurityPro 800 v2 Program Sheet Click HERE for Programming Keys A = 10 B = 11 C = 12 D = 13 E = 14 F = 15 Power Ratings 500mA if using 25VA Transformer.

and wants the interior protected (the motion detectors ON).

1. Close all protected doors and windows.

ARMING IN “STAY” MODE STAY is used when the user is inside the premises and

wants protection around the perimeter (the motion

detectors OFF).

2. Press the “STAY” key.

DISARMING SYSTEM Enter code.

2. Enter a master code. The “ready” light will flash.

3. Enter the 2-digit user number (example: “03” for user

4. Enter the new 4-digit user code. Note: To delete a

user code, enter * * * * for a 4-digit code.

5. The ready light will flash. If the code is rejected, the

6. If another user code needs to be programmed,

7. Press the “#” key while the ready light is flashing to

exit the User Code Programming Mode.

BYPASSING ZONES System must be in disarmed state.

2. Enter 1 or 2 digits indicating the zone you wish to

bypass. (Example: Press the “1” key for zone 1,

press “1” then “2” for zone 12.)

4. The corresponding zone light will illuminate indicating

the zone has been bypassed. Repeat steps #2 and #3 for

any other zone(s) that need to be bypassed.

5. Press the “#” key to exit the Bypass Mode. The bypass

light will stop flashing upon exiting the Bypass Mode.

All zones will automatically be unbypassed each time the

system is disarmed.

VIEW ALARM MEMORY 1. Press “8” “3.” The zone(s) that created the last alarm

2. The ALARM MEMORY feature will flash those zones

that created alarms and will light steady those zones that

were bypassed during the last alarm.

IDENTIFYING TROUBLES

FLASHING ARMED LIGHT The armed light will flash when there has been

an alarm during the previous arm cycle.

POWER LIGHT OFF No AC power.

POWER LIGHT FLASHING Low system battery.

FIRE LIGHT FLASHING Trouble with fire device or wiring.

ZONE LIGHT FLASHING RAPIDLY A zone is in a trouble condition.

SERVICE LIGHT IS ON Press “*2” for further information (indicated by

zone lights).

Zone 1 – System fault.

Zone 2 – Zone tamper.

Zone 5 – Zone trouble.

Ge Networx Nx 8

Zone 6 – Telephone trouble.

Zone 7 – Dialer failure.

Zone 8 – System lost time.

Enter “#” to exit mode.

ENTER CODE TO SILENCE TROUBLE BEEPS.

ENTER “*7” TO ATTEMPT TO RESET TROUBLES.

ENTER CODE TO CLEAR SERVICE LIGHT AFTER A PHONE TROUBLE HAS BEEN CLEARED.

SET CLOCK 1. Press “*97.”

3. Enter time as 4-digit military time.

Caddx Networx Nx 8

Download Operation & user’s manual of CADDX NX-8 Control Panel, Security System for Free or View it Online on All-Guides.com. This version of CADDX NX-8 Manual compatible with such list of devices, as: NX-8, NX-8e, NX6UB98, NX8EUA01, NX8UI00

Brand: CADDX

Category: Control Panel , Security System

Type: Operation & user’s manual

Model: CADDX NX-8 , CADDX NX-8e , CADDX NX6UB98 , CADDX NX8EUA01 , CADDX NX8UI00

Pages: 18

SECURITY SYSTEM NOTES

How to program caddx nx 8 wiring diagram

Installing/Service Company _________________________________

For Service Call __________________________________________

Central Station ___________________________________________

FUNCTION CODES

This system is  is not  partitioned.

 Fire Auxiliary Emergency Police

 Abort Delay (V) Cancel Alarm Forced Arming (V)

 Auto Bypass (V) Change Partitions Group Bypass (V)

 Battery Test Communicator Test Re Exit

(V) These features should not be enabled on UL listed systems.

Exit Delay Time __________Secondary Exit Delay Time ________

Entry Delay Time _________Secondary Entry Delay Time _______

01 _______________09 _______________17 _______________

02 _______________10 _______________18 _______________

03 _______________11 _______________19 _______________

04 _______________12 _______________20 _______________

05 _______________13 _______________21 _______________

06 _______________14 _______________22 _______________

07 _______________15 _______________23 _______________

Caddx Nx 8 User Manual

08 _______________16 _______________24 _______________

Related Products for CADDX NX-8

Related Manuals for CADDX NX-8

CADDX NX-8: Frequently viewed Manuals

How To Program Caddx Nx 8 Wiring